Abstract
Cr12MoV hardened steel is widely used in the manufacturing of stamping die because of its high strength, high hardness, and good wear resistance. As a kind of mainstream cutting technology, high-speed machining has been applied in the machining of Cr12MoV hardened steel. Based on the review of a large number of literature, the development of high-speed machining of Cr12MoV hardened steel was summarized, including the research status of the saw-tooth chip, cutting force, cutting temperature, tool wear, machined surface quality, and parameters optimization. The problems that exist in the current research were discussed and the directions of future research were pointed out. It can promote the development of high-speed machining of Cr12MoV hardened steel.
Keywords: Cr12MoV hardened steel, high-speed machining, machining mechanism, tool wear, surface quality, parameter optimization.
Graphical Abstract
[1]
X.K. Liu, "Development trend of mould industry", Scientific research, no. 007, pp. 290-290, 2014.
[3]
Y.S. Gao, "Present situation and development of die materials in China", Aeronautical Manufacturing Technology, no. 08, pp. 68- 69, 2008.
[4]
Y. Leng, and W.G. Huang, "Effect of heat treatment process on microstructure, hardness and wear resistance of Cr12MoV steel", Sichuan Metallurgy., vol. 32, no. 1, pp. 8-11, 2010.
[5]
Y. Liu, X.L. Liu, and J.D. Zhang, "Effect of deep cryogenic treatment on mechanical properties of Cr12MoV steel", heat treatment of metals, vol. 36, no. 8, pp. 38-41, 2011.
[6]
Y.F. Ren, Y.L. Zhang, Z.G. Zhao, and F. An, "J.T. Xue, Z.Y.Sun Yao, and J.B. Chang, “Enhanced surface properties and microstructure evolution of cr12mov using ultrasonic surface rolling process combined with deep cryogenic treatment", J. Mater. Eng. Perform., pp. 1059-9495, 2019.
[8]
X. Ai, "Present situation and Prospect of high speed cutting technology
and tool materials", World Manufacturing Engineering
Market, no. 3, pp. 32-36, 2001.
[10]
H. Zhang, "Finite element simulation of serrated chip in high speed
cutting", Tool Engineering, no. 01, pp. 29-3, 2005.
[11]
Q.B. Yang, Z.Q. Liu, and G.S. Su, "Research status and development of serrated chip formation mechanism in high speed cutting", Tool Engineering, vol. 45, no. 03, pp. 3-11, 2011.
[13]
L.H. Tang, C.X. Gao, H. Shen, X.J. Lin, and L. Zhang, "Mechanism of the crack propagation in the chip root in dry hard orthogonal turning of the hardened steel", International Journal of Mechanical Sciences, 2018.
[http://dx.doi.org/10.1016/j.ijmecsci.2018.02.020]
[http://dx.doi.org/10.1016/j.ijmecsci.2018.02.020]
[14]
Yu.J. Zhao, "W. Y., Q.Q. N., and H. Dong, “Experimental study on chip morphology of high speed cutting hardened die steel", Tool Engineering., vol. 47, no. 01, pp. 58-61, 2013.
[15]
F. Gong, J. Zhao, X. Ni, C.X. Liu, J.L. Sun, and Q.Z. Zhang, Wear and breakage of coated carbide tool in milling of H13 steel and SKD11 hardened steel., SN Applied Sciences, 2019, pp. 1-12.
[16]
L.H. Tang, H. Shen, Q.S. Chang, J. Yin, and X.J. Lin, "Experimental study on low, medium and high speed dry turning of high hardness, high strength and high wear resistance hardened steel", Modern Manufacturing Engineering, vol. 04, pp. 1-15, 2018.
[17]
L.L. Jin, and M. Chen, "Experiment on surface integrity of milling tool for hardened steel skD11", Transactions of Nanjing University of Aeronautics& Astronautics., vol. 24, pp. 158-163, 2007.
[18]
L.L. Jin, M. Chen, and Q.L. An, "Experimental study on the formation
mechanism of saw-tooth chips in SKD11 hard cutting",
China Mechanical Eng., vol. , no. 23, pp. 31-73, 2014.
[19]
H. Shen, J. Yin, L.H. Tang, Y.J. Sun, C.Y. Wu, and Y. Tian, "Experimental study on chips of low, medium and high speed hard
right angle cutting hardened steel", Manufacturing Technology
Machine Tool, vol. , no. 01, pp. 139-142, 2017.
[20]
D. Rath, S. Panda, and K. Pal, "Dry turning of AISI D3 steel using a mixed ceramic insert: A study", J. Mech. Eng. Sci., vol. 233, pp. 19-20, 2019.
[21]
H.N. Gao, X. Liu, and Z. Chen, "Cutting Performance and Wear/Damage Characteristics of PCBN Tool in Hard Milling", Appl. Sci. (Basel), vol. 9, no. 04, 2019.
[http://dx.doi.org/10.3390/app9040772]
[http://dx.doi.org/10.3390/app9040772]
[22]
C. Wang, F. Ding, D.W. Tang, L.J. Zheng, S.Y. Li, and Y.X. Xie, "Modeling and simulation of the high speed milling of hardened steel SKD11 (62 HRC) based on SHPB technology", Int. J. Mach. Tools Manuf., vol. 108, pp. 13-26, 2016.
[http://dx.doi.org/10.1016/j.ijmachtools.2016.05.005]
[http://dx.doi.org/10.1016/j.ijmachtools.2016.05.005]
[23]
J. Fu, and F.L. Wang, "Cr12MoV Cutting Physical Simulation and
Experimental Research", Modern Manufacturing Engineering, no.
6, pp. 93-98, 2014.
[24]
J. Yu, H. Dong, H.T. Zhang, and M. Li, "Study on cutting force of high speed cutting hardened die steel based on orthogonal experiment", Tool Engineering., vol. 46, no. 06, pp. 13-16, 2012.
[25]
G.V. Neelakanth, K.S. Ramesh, M.C.H. Alves, J.C.C. Rubio, and A.M. Abrão, "Machinability evaluation in hard milling of AISI D2 steel", Mater. Res., vol. 19, no. 2, pp. 360-369, 2016.
[http://dx.doi.org/10.1590/1980-5373-MR-2015-0263]
[http://dx.doi.org/10.1590/1980-5373-MR-2015-0263]
[26]
M.B. Mhamdi, S.B. Salem, M. Boujelbene, and E. Bayraktar, "Experimental study of the chip morphology in turning hardened AISI D2 steel", J. Mech. Sci. Technol., vol. 27, no. 11, pp. 3451-3461, 2013.
[http://dx.doi.org/10.1007/s12206-013-0869-1]
[http://dx.doi.org/10.1007/s12206-013-0869-1]
[27]
J.R. Xu, L.H. Tang, and J.L. Huang, "Experimental study on threedimensional
cutting forces of tool steels with different hardening
states in dry turning", Manuf. Technol. Machine Tool, pp. 59-62,
2014.
[28]
C.X. Yue, J. Ma, F. Liu, Y.H. Yang, J.Y. Zhang, and X.L. Liu, "Tool wear during precision hard cutting of die steel Cr12MoV", J. Harbin Uni. Sci. Tech., vol. 19, no. 05, pp. 56-125, 2014.
[29]
L.H. Tang, C. Gao, J. Huang, X.J. Lin, and J.P. Zhang, "Experimental investigation of the three-component forces in finish dry hard turning of hardened tool steel at different hardness levels", Int. J. Adv. Manuf. Technol., vol. 70, no. 9-12, pp. 1721-1729, 2014.
[http://dx.doi.org/10.1007/s00170-013-5423-x]
[http://dx.doi.org/10.1007/s00170-013-5423-x]
[30]
F. Gong, J. Zhao, Y.W. Jiang, H.W. Tao, Z.L. Li, and J. Zang, "Fatigue failure of coated carbide tool and its influence on cutting performance in face milling SKD11 hardened steel", Int. J. Refract. Met. Hard Mater., vol. 64, pp. 27-34, 2017.
[http://dx.doi.org/10.1016/j.ijrmhm.2017.01.001]
[http://dx.doi.org/10.1016/j.ijrmhm.2017.01.001]
[31]
C.X. Yue, H.T. Zhang, J. Ma, and X.L. Liu, "Hard milling process optimization of splicing die based on sudden change of milling force", J. Shenyang Uni. Tech., vol. 39, no. 02, pp. 153-158, 2017.
[32]
F. Jiang, L. Yan, and Y. Rong, "Orthogonal cutting of hardened AISI D2 steel with TiAlN-coated inserts-simulations and experiments", Int. J. Adv. Manuf. Technol., vol. 64, no. 9-12, pp. 1555-1563, 2013.
[http://dx.doi.org/10.1007/s00170-012-4122-3]
[http://dx.doi.org/10.1007/s00170-012-4122-3]
[33]
Q.S. Chang, H. Shen, L.H. Tang, Z. Lv, C.X. Gao, and X.J. Lin, "Finite element analysis of turning Cr12MoV based on hardness change", Tool Engineering., vol. 49, no. 11, pp. 33-35, 2015.
[34]
M.L. Zheng, D. Wu, L. Yang, and H. Ma, "Research on prediction
of milling force for corner milling of ball end milling cutter", Machinery
Design Manufacture, no. 04, pp. 85-88, 2017.
[35]
H.A. Kishawy, "An experimental evaluation of cutting temperatures during high speed machining of hardened d2 tool steel", Mach. Sci. Technol., vol. 6, no. 1, pp. 67-79, 2002.
[http://dx.doi.org/10.1081/MST-120003186]
[http://dx.doi.org/10.1081/MST-120003186]
[36]
P. Yang, X.K. Li, and M. Chen, "Comparison of surface integrity between milling and grinding hardened steel SKD11", J. Shanghai Jiaotong Univ., no. 04, pp. 582-585, 2007.
[37]
M. Chen, L.L. Jing, and X.K. Li, "The surface integrity in machining hardened steel skd11 for die and mold", Mach. Sci. Technol., vol. 11, no. 1, pp. 99-116, 2007.
[http://dx.doi.org/10.1080/10910340601174574]
[http://dx.doi.org/10.1080/10910340601174574]
[38]
R. Kumar, A.K. Sahoo, R.K. Das, A. Panda, and P.C. Mishra, "Modelling of Flank wear, Surface roughness and Cutting Temperature in Sustainable Hard Turning of AISI D2 Steel", Procedia Manufacturing., vol. 20, pp. 406-413, 2018.
[http://dx.doi.org/10.1016/j.promfg.2018.02.059]
[http://dx.doi.org/10.1016/j.promfg.2018.02.059]
[39]
J. Fu, and F.L. Wang, "Physical simulation and experimental research
on the cutting process of Cr12MoV", Modern Manuf. Eng.,
no. 06, pp. 93-98, 2014.
[40]
L.M. Xie, G. Cheng, and L. Jin, "Research on Cr12MoV cutting temperature prediction model based on orthogonal experiments", Tool Engineering., vol. 50, no. 01, pp. 30-33, 2016.
[41]
C.X. Yue, X.L. Liu, H. Shi, H.C. Deng, Y.F. Li, and Y.N. Chen, "Study on cutting force of die steel Cr12MoV in hard milling process", Tool Engineering., vol. 47, no. 12, pp. 13-16, 2013.
[42]
C. Yue, X. Liu, J. Ma, Z.J. Liu, F. Liu, and Y.H. Yang, "Hardening effect on machined surface for precise hard cutting process with consideration of tool wear", Chin. J. Mech. Eng., vol. 27, no. 6, pp. 1249-1256, 2014.
[http://dx.doi.org/10.3901/CJME.2014.0922.154]
[http://dx.doi.org/10.3901/CJME.2014.0922.154]
[43]
Z. Lv, H. Shen, L.H. Tang, Q.S. Chang, C.X. Gao, and X.J. Lin, "Prediction and analysis of tool wear in dry hard cutting with different hardness materials", Tool Engineering., vol. 49, no. 12, pp. 13-15, 2015.
[44]
X.C. Zhu, and L.P. Shen, "Experimental study on surface roughness
of hardened steel SKD11 by dry turning", Manufacturing
Technology Machine Tool, no. 12, pp. 31-33, 2009.
[45]
R. Izamshah, J. Mo, S. Ding, M. Arfauz, M.A. Azam, and M.S. Kasim, "Effect of parameter condition on surface roughness for machining AISI D2 hardened tool steel", J. Adv. Manuf. Technol., vol. 8, pp. 47-56, 2014.
[46]
L.H. Tang, C. Gao, J. Huang, H. Shen, and X.J. Lin, "Experimental investigation of surface integrity in finish dry hard turning of hardened tool steel at different hardness levels", Int. J. Adv. Manuf. Technol., vol. 77, no. 9-12, pp. 1655-1669, 2015.
[http://dx.doi.org/10.1007/s00170-014-6484-1]
[http://dx.doi.org/10.1007/s00170-014-6484-1]
[47]
X.C. Wang, Y.H. Zhou, and J. Zhao, "Study on surface roughness of ball end milling of hardened die steel based on orthogonal experiment", Tool Engineering., vol. 52, no. 07, pp. 27-30, 2018.
[48]
M.T. Bich, P.T. Hoa, B.T. Long, and D.T. Nguyen, "Experimental researching of thermal-assisted milling with induction on surface roughness of SKD11 steel", Appl. Mech. Mater., vol. 889, pp. 190-196, 2019.
[http://dx.doi.org/10.4028/www.scientific.net/AMM.889.190]
[http://dx.doi.org/10.4028/www.scientific.net/AMM.889.190]
[49]
Y.Y. Wang, H.J. Zhu, H. Chen, H.Q. Wang, J.Q. Chen, and D.H. Cai, "Cr12MoV Milling stability prediction and experimental research", J. Zhejiang Uni. Techno., vol. 45, no. 06, pp. 649-653, 2017.
[50]
W. Xu, M.L. Zheng, S.C. Yang, W. Zhang, and Y.H. Fan, "Experimental study on the influence of high speed milling hardened steel cutting edge on surface roughness", Aviation Precision Manuf. Technol., vol. 46, no. 05, pp. 57-59, 2010.
[51]
V.D. Patel, and A.H. Gandhi, "Analysis and modeling of surface roughness based on cutting parameters and tool nose radius in turning of AISI D2 steel using CBN tool", Measurement, vol. 138, pp. 34-38, 2019.
[http://dx.doi.org/10.1016/j.measurement.2019.01.077]
[http://dx.doi.org/10.1016/j.measurement.2019.01.077]
[52]
H.N. Gao, C.X. Yue, and X.L. Liu, "Simulation of Surface Topography Considering Cut-in Impact and Tool Flank Wear", Science Letter, vol. 9, no. 4, pp. 222-226, 2019.
[http://dx.doi.org/10.3390/app9040732]
[http://dx.doi.org/10.3390/app9040732]
[53]
L.H. Tang, H. Shen, Q.S. Chang, J. Yun, and X.J. Lin, "Study on
the formation mechanism of surface modification layer of Dry
Turning Hardened Steel", Manuf. Technol. Machine Tool, no. 02,
pp. 122-256, 2017.
[54]
C.X. Yue, Z.N. Zhong, J. Ma, and Y.H. Yang, "Research on Formation of Metamorphic Layer in Hard Cutting Process of Cr12MoV", J. Harbin Uni. Sci. Technol., vol. 20, no. 06, pp. 32-36, 2015.
[55]
S.K. Rajbongshi, M.A. Singh, and D.K. Sarma, "A comparative study in machining of AISI D2 steel using textured and non-textured coated carbide tool at the flank face", J. Manuf. Process., vol. 36, pp. 360-372, 2018.
[http://dx.doi.org/10.1016/j.jmapro.2018.10.041]
[http://dx.doi.org/10.1016/j.jmapro.2018.10.041]
[56]
C.X. Yue, X.L. Liu, J. Ma, X. Liu, and G.X. Ren, "Study of surface residual stress in hard turning of die steel Cr12mov", Key Eng. Mater., vol. 589-590, pp. 33-37, 2013.
[http://dx.doi.org/10.4028/www.scientific.net/KEM.589-590.33]
[http://dx.doi.org/10.4028/www.scientific.net/KEM.589-590.33]
[57]
C.X. Yue, L. Zhu, L. Feng, J. Liu, S.Y. Hao, and G.X. Ren, "Influences of tool wear on residual stress and fatigue life of workpiece in hard cutting process", J. Harbin Institute Technol., vol. 025, no. 005, pp. 61-69, 2018.
[58]
C.X. Yue, Y.H. Yang, F. Liu, and X.L. Liu, "Study on the formation of deteriorated layer on machined surface during precision hard cutting", Nanotechnology and Precision Engineering., vol. 12, no. 03, pp. 222-226, 2014.
[59]
C.Y. Wu, H. Shen, J. Yin, Y. Tian, and L.H. Tang, "Simulation and analysis of factors affecting surface residual stress of dry-cut parts", Tool Engineering., vol. 51, no. 01, pp. 18-21, 2017.
[60]
L. Wang, J.E. Wang, X.H. Guo, H.L. Wu, and G.M. Huang, "Study
on tool life of carbide end milling cutter for milling Cr12MoV
hardened steel", Modern Manuf. Eng., no. 06, pp. 133-137, 2016.
[61]
L. Tang, Y. Sun, B. Li, J.H. Shen, and G.L. Meng, "Wear performance and mechanisms of PCBN tool in dry hard turning of AISI D2 hardened steel", Tribol. Int., vol. 132, pp. 228-236, 2019.
[http://dx.doi.org/10.1016/j.triboint.2018.12.026]
[http://dx.doi.org/10.1016/j.triboint.2018.12.026]
[62]
M.A. Khan, A.S. Kumar, S.T. Kumaran, M.U. Kumar, and T.J. Ko, Effect of tool wear on machining gfrp and aisi d2 steel using alumina based ceramic cutting tools., Silicon, 2018.
[63]
J. Dureja, R. Singh, and M.S. Bhatti, "Optimizing flank wear and surface roughness during hard turning of AISI D3 steel by taguchi and RSM methods", Prod. Manuf. Res., vol. 2, no. 1, pp. 767-783, 2014.
[http://dx.doi.org/10.1080/21693277.2014.955216]
[http://dx.doi.org/10.1080/21693277.2014.955216]
[64]
J.M. Xiao, "Experimental study on milling tool life for SKD11 steel and optimization of cutting parameters", Machine Tool & Hydraulics., vol. 42, no. 18, pp. 108-112, 2014.
[65]
M.J. Mir, M.F. Wani, S. Banday, and B. Parveez, "Influence of cutting fluid conditions on tool wear and surface roughness in hard turning AISI-D2 Steel using mixed ceramic tools", J. Phys. Conf. Ser., vol. 1240, no. 012109, pp. 1742-6596, 2019.
[66]
N. CamuCu , and E. Aslan, "A comparative study on cutting tool
performance in end milling of AISI D3 tool steel", J. Mater. Process.
Technol., vol. 170, no. 1-2, pp. 121-126, 2005.
[http://dx.doi.org/10.1016/j.jmatprotec.2005.04.111]
[http://dx.doi.org/10.1016/j.jmatprotec.2005.04.111]
[67]
H. Bouchelaghem, M.A. Yallese, T. Mabrouki, A. Amirat, and J.F. Rigal, "Experimental investigation and performance analyses of cbn insert in hard turning of cold work tool steel (d3)", Mach. Sci. Technol., vol. 14, no. 4, pp. 471-501, 2010.
[http://dx.doi.org/10.1080/10910344.2010.533621]
[http://dx.doi.org/10.1080/10910344.2010.533621]
[68]
J. Yu, Y.W. Zhao, Q.Q. Ni, and H. Dong, "Comparative experimental study on tool wear of high-speed cutting hardened die steel", Diamond & Abrasives Engineering., vol. 33, no. 01, pp. 48-52, 2013.
[69]
Y. Su, N. He, and L. Li, "Effect of cold air cutting on tool wear of hard-to-machine materials in high speed cutting", Tribology, vol. 30, no. 05, pp. 485-490, 2010.
[70]
O. Zbek, and H. Saruhan, "The effect of vibration and cutting zone temperature on surface roughness and tool wear in eco-friendly MQL turning of AISI D2", J. Mater. Res. Technol., vol. 9, no. 3, pp. 2762-2772, 2020.
[http://dx.doi.org/10.1016/j.jmrt.2020.01.010]
[http://dx.doi.org/10.1016/j.jmrt.2020.01.010]
[71]
J.T. Chorng, and K.Y. Yung, "Determination of optimal parameters for skd11 cnc turning process", Adv. Manuf. Processes., vol. 23, no. 4, p. 6, 2008.
[72]
L.H. Tang, J.L. Huang, C.X. Gao, and W.C. Luo, "Parameter optimization
of surface roughness in precision dry hard turning of
hardened tool steels", Manuf. Technol. Machine Tool, no. 1, pp.
112-114, 2012.
[73]
J. Song, C. Huang, M. Lv, B. Zou, H.L. Liu, and J. Wang, "Cutting performance and failure mechanisms of TiB2-based ceramic cutting tools in machining hardened Cr12MoV mold steel", Int. J. Adv. Manuf. Technol., vol. 70, no. 1-4, pp. 495-500, 2014.
[http://dx.doi.org/10.1007/s00170-013-5296-z]
[http://dx.doi.org/10.1007/s00170-013-5296-z]
[74]
R.D. Sudhansu, K. Amaresh, and D. Debabrata, "Prediction of optimal design on tool wear and workpiece surface temperature in turning of AISI D2 steel", J. Eng. Innova. Res., vol. 83-86, pp. 746-755, 2013.
[75]
C.X. Yue, L. Zhu, J. Liu, L. Feng, and N. Jiang, "Optimization of
hard milling processing for convex surface joining die with milling
force control", Mechanical ence and Technology for Aerospace
Engineering, vol. 37, no. 4, pp. 568-574, 2018.
[76]
F.T. Yih, "Parameter design optimisation of computerised numerical control turning tool steels for high dimensional precision and accuracy", Mater. Des., vol. 27, no. 8, pp. 665-675, 2006.
[77]
H. Aouici, H. Bouchelaghem, M.A. Yallese, M. Elbah, and B. Fnides, "Machinability investigation in hard turning of AISI D3 cold work steel with ceramic tool using response surface methodology", Int. J. Adv. Manuf. Technol., vol. 73, no. 9-12, pp. 1775-1788, 2014.
[http://dx.doi.org/10.1007/s00170-014-5950-0]
[http://dx.doi.org/10.1007/s00170-014-5950-0]
[78]
R.D. Patel, and S.N. Bhavsar, "Experimental investigation during
end milling of AISI D2 tool steel using AlCrN coated tool", Materials
today: proceedings, vol. 22, pp. 2647-2656, 2020.
[http://dx.doi.org/10.1016/j.matpr.2020.03.396]
[http://dx.doi.org/10.1016/j.matpr.2020.03.396]
[79]
S.B. Chandgude, P.J. Pawar, and M. Sadaiah, "Process parameter optimization based on principal components analysis during machining of hardened steel", Intern. J. Indus. Eng. Comput., vol. 6, no. 3, pp. 379-390, 2015.
[http://dx.doi.org/10.5267/j.ijiec.2015.2.004]
[http://dx.doi.org/10.5267/j.ijiec.2015.2.004]
Related Books
Advanced Characterization Technologies for Secondary Batteries
Design and Construction of Buildings and Foundations with Illustrative Examples
Robotics and Automation in Industry 4.0
Biomedical Applications of Perovskites: The Era of Bio-Piezoelectric Systems
Smart Kinematics For Modern Engineering Students
Computational Modeling and Simulation in Biomedical Research
Introduction to Advanced Soft Robotics
Intelligent Technologies for Research and Engineering
The Production of Biodiesel and Related Fuel Additives
Intelligent Technologies for Research and Engineering
Article Metrics
10
1