Login Register Cart 0
Generic placeholder image

Recent Patents on Engineering

Editor-in-Chief

ISSN (Print): 1872-2121
ISSN (Online): 2212-4047

Back
Journal Home About Journal Editorial Board Journal Insight Current Issue Volumes/Issues
Subscribe
General Review Article

Causes of Deterioration in XLPE MV Cables: A Review

Author(s): Ifetayo Oluwafemi, Ayodeji Olalekan Salau* and Timothy Laseinde

Volume 15, Issue 2, 2021

Published on: 17 January, 2020

Page: [218 - 224] Pages: 7

DOI: 10.2174/1872212114666200117110502

Price: $65

Abstract

Background: Power failure and its related challenges is the cause of low economic development in most developing countries. Power failure is sometimes caused by the constant technical problems experienced by power network components which are being used for electric power transmission and distribution.

Most distribution and transmission substations operate at medium voltages. Medium Voltage (MV) cables provide an efficient means of power distribution to customers. In recent times, medium voltage cables with cross-linked Polyethylene are most commonly used in modern power systems compared to the classical or paper-insulated cables due to their high resistance to Partial Discharge (PD), good electrical properties, and ability to operate at high temperature levels. However, during the process of transmission the deterioration of a cable is inevitable. This reduces the reliability and efficiency of the transmission and distribution process, which is of course a serious concern to power engineers and consumers.

Owing to the challenges experienced from the degradation of MV XLPE cables, it has become highly imperative to investigate the causes of failure in power network cables used for the transmission and distribution of electric power.

Methods: A comprehensive review was carried out to understand the fundamental causes of MV XLPE degradation. This was pivotal in adopting the right monitoring technique for the MV XLPE cable.

Results: The results show that the major causes of MV network cable faults are attributed to either material related or external causes. It was also discovered that there are different fault rates for different MV cable types. Further discoveries show that the XLPE cables failure rate is minimal compared to the Nordic Oil-paper cables which are said to have an average faults occurrences detection of about 4-5 times higher than that of the XLPE cables. Oil paper cables experience high failure rates and in addition experience substantial defects in their cable joints.

Conclusion: This paper presented a comprehensive review of the causes of MV XLPE cable degradation and proffers solutions to the lingering challenges associated with MV XLPE cables.

Keywords: Medium voltage, XLPE cable, faults, deterioration, insulation, electric power.

Graphical Abstract

[1]
J. Orrit, J. Canadas, J. Sellares, and J. Belana, "Identification of dipolar relaxations in dielectric spectra of mid-voltage cross-linked polyethylene cables", J. Electrost., vol. 69, no. 2, pp. 119-125, 2011.
[http://dx.doi.org/10.1016/j.elstat.2011.01.005]
[2]
Y. Kim, J. Kwon, J. Park, and K. Lim, "Electrical conduction characteristics of low-density polyethylene and cross-linked polyethylene nanocomposite for high voltage direct current power cable", J. Nanosci. Nanotechnol., vol. 16, no. 11, pp. 11757-11761, 2016.
[http://dx.doi.org/10.1166/jnn.2016.13588]
[3]
K.A. Ibrahim, M.T. Au, C.K. Gan, and J.H. Tang, "System-wide MV distribution network technical losses estimation based on reference feeder and energy flow model", Int. J. Electr. Power Energy Syst., vol. 93, pp. 440-450, 2017.
[http://dx.doi.org/10.1016/j.ijepes.2017.06.011]
[4]
G. He, H. Zhang, Y. Xu, and X. Lu, "China’s clean power transition: current status and future prospect", Resour. Conserv. Recycling, vol. 121, pp. 3-10, 2017.
[http://dx.doi.org/10.1016/j.resconrec.2016.11.003]
[5]
B. Marungsri, A. Rawangpai, and N. Chomnawang, "Investigation lifetime model of 22 kV XLPE cable for distribution system applications in Thailand", WSEAS Transactions on Circuits and Systems, vol. 10, no. 2, pp. 185-197, 2011.
[6]
C. Malliou, A. Karlis, M.G. Danikas, and B. Lloyd, "A short review on the offshore wind turbine generator windings’ insulation and the effect of water droplets and salinity", Stress, vol. 2, no. 3, 2016.
[7]
S.S. Refaat, and M.A. Shams, A review of partial discharge detection, diagnosis techniques in high voltage power cables .
[http://dx.doi.org/10.1109/CPE.2018.837260]
[8]
N. Hampton, Medium Voltage Cable System Issues. 2016.,
[9]
X. Duan, M. Tang, F. Lin, and H. Ye, "Analysis on the breakdown of main insulation on the middle joint of 220 kV power cable", High Voltage App, vol. 45, no. 6, pp. 142-144, 2009.
[10]
H. Li, Z. Zhou, and P. Chen, "Fault analysis for 110 kv and the above hv cross-linking cable system", Electrical Equipment, vol. 8, pp. 9-13, 2004.
[11]
G. Mazzanti, "Effect of the combined electro-thermal stress, load cycling and thermal transients on polymer-insulated high voltage ac cable life , IEEE Power Engineering Society General Meeting, 2005, San Francisco, CA, 2005, pp. 95-102",
[12]
Y. Wang, S. Zheng, and L. Chen, "Statistics and analysis of power cable faults in Jiangxi power grid", Jiangxi Electr. Power, vol. 37, no. 5, pp. 55-57, 2013.
[13]
M. Wang, State grid corporation of China’s yearbook 2011., China Electric Power Press: China, 2012, p. 566.
[14]
J. Luo, Y. Qiu, and L. Yang, "Operation fault analysis of CLPE power cable above 10 kV", High Voltage Engineering, vol. 29, no. 6, pp. 14-16, 2003.
[15]
Y. Song, and B. Wang, "Survey on the reliability of power electronic systems", IEEE Trans. Power Electron., vol. 28, no. 1, pp. 591-604, 2013.
[http://dx.doi.org/10.1109/TPEL.2012.2192503]
[16]
O. Saito, J. Vepsäläinen, A. Hämäläinen, and M. Loukkalahti, "Improving reliability by focusing on the quality and condition of medium-voltage cables and cable accessories", In: CIRED-Open Access Proceedings Journal,. vol. 1, 2017, 229-232, 2017.
[17]
ISO (International Organization for Standardization), "ISO 55000: Asset management–overview, principles, and terminology,",,
[18]
A. Houston, I. Denizet, and F. Deleu, "Life cycle assessment improvement for medium voltage cable for french market", 9th International Conference on Insulated Power Cables Versailles France, 2015pp. 1-5
[19]
G. Chen, M. Hao, Z. Xu, A. Vaughan, J. Cao, and H. Wang, "Review of high voltage direct current cables", CSEE Journal of Power and Energy Systems, vol. 1, no. 2, pp. 9-21, 2015.
[http://dx.doi.org/10.17775/CSEEJPES.2015.00015]
[20]
N. Boudinet, J. Charvet, and M. Dory, "Design studies for French submarine links", 9th International Conference Insulated Power Cables Versailles, France, 2015pp. 1-5
[21]
W. Higinbotham, Review of Medium-Voltage Asset Failure Investigations The Premier Electrical Maintenance and Safety Event. 1- 17,
[22]
Y. Zhou, J. He, J. Hu, X. Huang, and P. Jiang, "Evaluation of polypropylene/polyolefin elastomer blends for potential recyclable HVDC cable insulation applications", IEEE Trans. Dielectr. Electr. Insul., vol. 22, no. 2, pp. 673-681, 2015.
[http://dx.doi.org/10.1109/TDEI.2015.7076762]
[23]
B. Dang, J. He, and J. Hu, "Space charge behaviors of PP/PER/ZnO nanocomposites for recyclable HVDC cable", 9th Int. Conf. Insulated Power Cables Versailles, France, 2015pp. 1-6
[24]
Y. Zhou, J. He, and J. Hu, "Eco-friendly nanodielectrics with enhanced thermal and electrical properties for HVDC cable insulation", 9th Int. Conf. Insulated Power Cables, 2015pp. 1-5
[25]
"HD 620 S2:2010, " Distribution cables with extruded insulation for rated voltages from 3,6/6 (7,2) kV up to and including 20,8/36 (42) kV,", Cenelec, 2010.,
[26]
"I.E.C. 60502-2, "Power cables with extruded insulation and their accessories for rated voltages from 1 kV (um = 1,2 kV) up to 30 kV (um = 36 kV),",",,
[27]
X. Chen, Y. Xu, X. Cao, and S. Gubanski, "Electrical treeing behavior at high temperature in XLPE cable insulation samples", IEEE Trans. Dielectr. Electr. Insul., vol. 22, no. 5, pp. 2841-2851, 2015.
[http://dx.doi.org/10.1109/TDEI.2015.004784]
[28]
J.Z. Hansen, "Results from Danish failure statistics for medium voltage XLPE cables", Proceedings of 22th CIRED Conf.Stockholm, Sweden, 2013pp. 1-4
[http://dx.doi.org/10.1049/cp.2013.1097]
[29]
E. Maggioli, H. Leite, and C. Morais, "A survey of the Portuguese MV underground cable failure", 13th International Conference of European Energy Market (EEM), Porto, Portugal, 2016, pp. 1-41.,
[http://dx.doi.org/10.1109/EEM.2016.7521217]
[30]
D. Williams, "Cable accessory failure analysis ICC Educational Session (NEETRAC Publications,, 2010 Georgia, USA,",
[31]
R. Badru, O. Akinwale, A. Salau, K. Olorunyomi, J. Alwadood, and A. Atijosan, "Assessment of geo-spatial proximity and magnetic pollution from 132kV and 330kV power transmission lines to infrastructures in Osogbo, Nigeria", Eskişehir Teknik Üniversitesi Bilim ve Teknoloji Dergisi B-Teorik Bilimler, vol. 7, no. 1, pp. 81-93, 2019.
[http://dx.doi.org/10.20290/aubtdb.407794]
[32]
J. Granado, C. Álvarez-Arroyo, A. Torralba, J.A. Rosendo-Macías, J. Chávez, and M. Burgos-Payán, "Time-domain analysis of partial discharges envelope in medium voltage XLPE cables", Electr. Power Syst. Res., vol. 125, pp. 220-227, 2015.
[http://dx.doi.org/10.1016/j.epsr.2015.04.009]
[33]
C. Olsson, B. Källstrand, B. Ma, M. Lundmark, K. Johansson, S. Arnsten, A. Abbasi, M. Saltzer, and M. Jeroense, Space charge distribution in XLPE plates with non-uniform conductivity., JiCable, 2015.
[34]
J. Granado, A. Torralba, and C. Álvarez-Arroyo, "Modeling dispersion of partial discharges due to propagation velocity variation in power cables", Electr. Power Syst. Res., vol. 137, pp. 124-132, 2016.
[http://dx.doi.org/10.1016/j.epsr.2016.04.005]
[35]
F. Frutos Rayego, M. Acedo García, M. Mudarra, J. Belana, J. Orrit, J. Diego, J. Cañadas, and J. Sellarés, "Effect of annealing on conductivity in XLPE mid-voltage cable insulation", J. Electrost., vol. 65, no. 2, pp. 122-131, 2007.
[http://dx.doi.org/10.1016/j.elstat.2006.07.015]
[36]
A. Attia, "Analysis of failure in power cables for preventing power outage in Alexandria electricity distribution company in Egypt", CIRED - Open Access Proceedings Journal,, 2017, pp. 20-24, 2017..
[http://dx.doi.org/10.1049/oap-cired.2017.0895]
[37]
M. Manyahi, R. Thottappillil, and M. Leijon, "Transfer of transient surge voltage through XLPE cable winding transformer (Dryformer) circuits", Int. J. Electr. Power Energy Syst., vol. 27, no. 8, pp. 602-609, 2005.
[http://dx.doi.org/10.1016/j.ijepes.2005.06.007]
[38]
M. Lanza, M. Fu, E. Neagu, L. Dissado, J. Marat-Mendes, A. Tzimas, and S. Zadeh, "Space charge analysis of electrothermally aged XLPE cable insulation", J. Non-Cryst. Solids, vol. 353, no. 47, pp. 4462-4466, 2007.
[39]
Y. Yang, D.M. Hepburn, C. Zhou, W. Zhou, W. Jiang, and Z. Tian, "On-line monitoring and analysis of the dielectric loss in cross-bonded HV cable system", Electr. Power Syst. Res., vol. 149, pp. 89-101, 2017.
[http://dx.doi.org/10.1016/j.epsr.2017.03.036]
[40]
M. Bao, X. Yin, and J. He, "Structure characteristics of electrical treeing in XLPE insulation under high frequencies", Physica B, vol. 406, no. 14, pp. 2885-2890, 2011.
[http://dx.doi.org/10.1016/j.physb.2011.04.055]
[41]
Y. Xu, W. Mei, H. Yang, C. Li, and G. Song, "Insulation Breakdown Influence Factors and Development of Cross-linked Polyethylene Cable", 2nd Annual International Conference on Advanced Material Engineering (AME 2016), 2016pp. 584-588
[http://dx.doi.org/10.2991/ame-16.2016.96.]

Rights & Permissions Print Cite
Article Metrics
5
1
© 2024 Bentham Science Publishers | Privacy Policy